Lift Station Repair: Submersible and Grinder Pump Service
Pump pull and assessment, seal and bearing replacement, impeller and rail service, controls and float checks, and performance testing for the whole station.
Who repairs sewage and wastewater lift stations?
Brabazon repairs lift stations across the Upper Midwest, servicing the submersible and grinder pumps along with the rails, controls, and floats that run them. Every job starts by pulling and assessing the pumps, then moves through seal and bearing replacement, impeller and rail service, control and float checks, and a performance test so the station handles its flow reliably. Because overflows are not an option, we treat the station as a system. If a station is down, call 800.825.3222.
What we service
A lift station moves wastewater from a low collection point up to where gravity can carry it onward, so a failure risks backup and overflow. We service the complete station: submersible sewage pumps, grinder pumps, and trash-handling pumps, plus the guide rails and discharge connections, check valves, level floats and transducers, pump alternators, and the control panel. Servicing the pumps without the controls and rails is how a rebuilt pump ends up back on the bench, so we look at the whole station.
Typical scope of work
Station repair follows a consistent path and adjusts to what the assessment finds:
- Pump pull and assessment: lift the pumps off the rails, inspect the motor, volute, impeller, seals, and bearings, and check for water intrusion.
- Seal and bearing replacement: renew mechanical seals and bearings to keep water out of the motor and restore reliable running.
- Impeller and rail service: service or replace the impeller or grinder cutters, and check the guide rails, base elbow, and check valves.
- Controls and float checks: verify floats, transducers, alternators, and the panel so the pumps call and alternate correctly.
- Performance testing: confirm the station handles its design flow and the pumps alternate as intended before it returns to duty.
Pump categories for lift stations
Lift station repair centers on the pumps that do the work. Match your station equipment to its category for selection and service guidance:
For process and transfer pumps outside the station, see the broader industrial pump repair service.
Industries and utilities we support
Lift stations serve municipal collection systems and industrial plants alike. We support station service across:
- Wastewater treatment collection and pumping stations
- Manufacturing plant sump and effluent stations
- Food and beverage process wastewater stations
Station alarming or overflowing? Talk to an engineer
Tell us the station configuration, the pumps, and the alarm or symptom, and an engineer will scope the repair. Need a bypass while the station is serviced? Ask about a rental trash or submersible pump.
Lift station repair questions, answered first
What does lift station repair cover?
Lift station repair covers the whole station as a system: the submersible or grinder pumps, the guide rails and discharge connections, the level controls and floats, and the panel that runs them. We pull and assess the pumps, service seals, bearings, and impellers, check the rail and check-valve hardware, and verify the controls call the pumps correctly. Treating the station as a system is what keeps a repaired pump from failing again on a control or rail fault.
Why did my lift station pump fail?
The most common causes are seal failure that lets water into the motor, impeller damage or clogging from rags and solids, worn bearings, and control or float faults that let a pump run dry or short-cycle. Grinder stations add cutter wear to that list. We look past the failed pump to the floats, check valves, and run pattern so the repair fixes the cause rather than just swapping a burned-out motor.
Do you service the controls and floats, not just the pumps?
Yes. A lift station is only as reliable as its level controls, so we check floats, transducers, alternators, and the control panel along with the pumps. A perfectly rebuilt pump still fails prematurely if a stuck float makes it short-cycle or run dry, so controls and floats are part of a proper station assessment, not an add-on.
How do you handle a station that keeps clogging?
Chronic clogging usually points to the wrong impeller style or an undersized pump for the solids in the flow, not just debris. We review what the station actually handles and can recommend a non-clog or grinder configuration suited to the waste stream, along with float settings that keep solids moving. That way the repair addresses the reason it clogs instead of clearing the same jam repeatedly.
Should I rebuild the station pumps or replace them?
Rebuild when the motor and volute are sound and only seals, bearings, or impellers have worn, which covers a lot of station service. Replacement makes sense when the motor is water-damaged beyond repair, the pump is undersized for the current flow, or the impeller style is wrong for the solids. We assess each pump and recommend the path that keeps the station reliable and the overflow risk low.
Request a lift station repair quote
Send the station configuration, the pump make and model, and the alarm or symptom you are seeing, and an engineer will follow up with a scope. Urgent? Call 800.825.3222, answered 24/7.
Request a Quote for lift station repair
Request received. If you need someone now, call 800.825.3222.
Please fill in all required fields (name, company, email, phone, preferred contact method, ZIP, and city), or call 800.825.3222.